|
Base
Unit
|
|
Dimensions
|
Length 30"
Width 18.5" Height 19.5" |
|
Shipping
Weight
|
Brush
and base Units - 65 pounds
|
|
Net
Weight
|
Base
Unit - 36 pounds
|
|
Solution
Tank
|
2
gallons liquid.
|
|
Recovery
Tank
|
1
gallon liquid. Capacity
|
|
Power
Supply
|
115
volt, 50-60 Hertz, 10.5 amperes. 220 volt, 50-60 Hertz, 5.5 amperes.
|
|
Motor
Rating
|
.5
H.P.
|
|
Motor
Speed
|
16,000
R.P.M. (full-load).
|
|
Wattage
|
1150
watts
|
|
Secondary
Power Supply
|
24
volt D.C. (built into base Unit) with silicon diode rectifier.
|
|
Controls
|
Rocker
type switch mounted on panel controls motor and power to 24 volt
receptacle. Toggle switch to control polarity of 24 volt receptacle.
|
|
Power
Cord
|
30
ft. non-marring, #16 gauge 3 wire.
|
|
Lubrication
Requirements
|
None.
|
|
Dirt
and Foam Recovery
|
Wet
and dry vacuum system with dacron filter bag equipped with quick
connect and disconnect 15' long. 1.25" inside diameter hose and
nozzle.
|
|
Operating
Principle
|
In
the base unit, air and detergent are mixed under pressure and blown
thru a media to create a dense low moisture foam which is delivered
by air pressure thru a 2-channel hose to the light weight low voltage
brush unit and discharged onto its two counter rotating brushes.
The scrubbing action of the brushes in the detergent foam loosens
the dirt which is then removed by vacuuming. The wet and dry vacuum
system is an integral part of the base unit. It pulls dirt and foam
into the recovery tank where the dirty solution is collected, the
air is filtered and exhausted to the atmosphere.
|
|
Brush
Unit
|
|
Dimentions
|
Length
10" Width 4.5" Height 8" 2-channel hose 15'.
|
|
Net
Weight
|
Brush
Unit with 2-channel hose - 8 pounds. Brush Unit without 2-channel
hose - 4 pounds.
|
|
Motor
|
1/10th
H.P. @ 7,300 R.P.M. (full load) 24 volt D.C. Sealed unit. No lubrication
required.
|
|
Brush
Speeds
|
Inner
- 750 R.P.M. Outer - 375 R.P.M.
|
|
First
Stage Drive Train
|
Hard
coat surface treated, maintenance-free metal gears.
|
|
Second
Stage Drive Train
|
Spur
gears, foam lubricated.
|
|
Brush
Construction
|
High
density polyethylene backs with straight bristle tynex tufts. Inner
Brush Dia. - 2.4375", Outer Brush Dia. - 4.25" Bristle Length -
1.0" (Available: Black,
stiffer bristle for carpet).
|
|
Controls
Motor
and Foam
|
A
single, three position toggle switch permits fingertip control of
brush unit drive motor, and selective, full, or intermittent flow
of foam generated by the base Unit.
|
|
Brush
Unit Color
|
Von
Schrader Gray scuff resistant ABS molded over aluminum.
|
|
Foam
Shroud, Handle
|
White
polyethylene foam shroud, black vinyl Grip.
|
|
Brush
Unit Bearings
|
High
speed ball type-double sealed.
|
|
Warranty
|
Special 1
year warranty on all parts and labor. |
We prefer a personalized order process therefore, please telephone us toll
free (in the USA) at
1-800-826-1600 between 8:15am and 4:30pm central time for a customer service
representative.